How can the solar controller be set up to save energy

<p>Lithium battery sales phone number</p>

Solar energy controller saves electricity

How to set up the solar controller using bright long save electricity, solar energy controller debug mode how to set up, how to set up the solar controller normally open mode, light-control solar controller model how to set up, how to set up the solar controller control mode, only know how to set up the solar controller can know how to use more save electricity, solar controller, of course, the premise is want to know can recharge source of motivation, don't know the controller charging source is special trouble, his hands on setting is also a confused.

Solar controller work MODE setting method: press the switch button for 5 seconds, MODE (MODE) display digital LED flashing, loosen the button, each time you press the switch a number, until the LED display of the number of users from the table on the selected model corresponds to the number or stop button, until the LED digital flicker free setup is completed. Each time the button is pressed, the LED will be lit up and the set value can be observed.

1543323932841357

2. Setting method of pure light control mode of solar controller: when there is no sunlight, the light intensity falls below the starting point, the controller delays 10 minutes to confirm the start signal, and then the load is turned on and the load starts to work; When there is sunlight, the light intensity rises above the starting point, and the controller delays 10 minutes to turn off the output signal after confirming the shutdown of the output signal, and the load stops working.

Setting method of single-period mode of solar controller: start process is the same as before. When the load reaches the set time, the load will be closed. The time setting is shown in the table below.

General controller setting method: this mode only cancels the light control, time control function, output delay and related functions, and retains all other functions as general controller.

Setting method: it is used for system debugging. It is the same as the pure light control mode, only cancelling the 10min delay of judging the control output of the light signal and keeping all other functions. If there is light signal, it will turn off the output of the load end; if there is no light signal, it will turn on the output of the load end. It is convenient to check the correctness of system installation during installation and debugging.

1543323954309269

Vi. Introduction to several modes of solar controller:

1. Pure light control mode: when there is no sunlight, the light intensity drops to the starting point, the controller delays 10 minutes to confirm the start signal, and then opens the load according to the set parameters, and the load starts to work; When there is sunlight, the light intensity rises to the starting point, and the controller delays 10 minutes to close the output after confirming the shutdown signal, and the load stops working.

2. Light control + time control mode: the starting process is the same as that of pure light control. When the load reaches the set time, it will shut down automatically and set the time for 1-14 hours.

3. Manual mode: in this mode, users can control the opening and closing of the load by pressing the button, regardless of whether it is in daytime or at night. This mode is used for some special load situations or debugging.

4. Debugging mode: it is used for system debugging. When there is light signal, the load is turned off; when there is no light signal, the load is turned on.

5. Normally open mode: the power on load always keeps the output state. This mode is suitable for the load that needs 24-hour power supply.

Seven, how to set the solar controller several common instructions:

1. Charging and overvoltage indication: when the system is connected normally and sunlight hits the solar panel, the charging indicator light (1) is always green, indicating that the charging circuit of the system is normal; When the charging indicator light (1) appears green quick flashing, it indicates that the system is overvoltage. For the treatment, see the fault treatment content. In the charging process, PWM mode is used. In case of over-discharge, the charging voltage should be raised and maintained for 10 minutes, and then reduced to the direct charging voltage and maintained for 10 minutes to activate the battery and avoid sulfide crystallization, and finally reduced to the floating charging voltage and maintain the floating charging voltage. If no discharge has occurred, there will be no lifting charge mode in case the battery loses water. These automatic control processes will enable the battery to achieve the best charging effect and ensure or extend its service life.

2. Battery status indicator: when the battery voltage is in the normal range, the status indicator (2) is always green; The status indicator light after filling is green slow flashing; The status indicator turns orange when the battery voltage drops to under voltage. When the battery voltage continues to drop to the over-discharge voltage, the status indicator (2) will turn red, and at this time, the controller will automatically turn off the output to remind the user to replenish the power in time. When the battery voltage returns to the normal working range, it will automatically enable the power output to turn on, and the status indicator (2) will turn green;

3. Load indication: when the load is on, the load indicator light (3) is always on. If the load current exceeds the rated current of the controller by 1.25 times for 60 seconds, or the load current exceeds the rated current of the controller by 1.5 times for 5 seconds, the indicator light (3) is red slow flashing, indicating overload, and the controller will close the output. When the load or load side short circuit fault, the controller will immediately turn off the output, indicator light (3) flash. When the above phenomenon occurs, the user should carefully check the load connection. After disconnecting the faulty load, press the button once and the normal work will resume after 30 seconds, or wait until the next day to work normally.

1543323987962362

How to set the solar controller is better. We also suggest setting the solar street lamp controller in this way. It can work continuously with the solar street lamp with 12V lithium battery, so as to better manage the battery.

How to set the parameters of the solar street lamp controller?

1. Press the setting button of the switch for 5 seconds, the MODE displays the digital LED flashing, release the button, and convert a number every time, until the number displayed by the LED is matched with the number corresponding to the MODE selected by the user from the table, the button will be stopped, and the setting will be completed when the LED number does not flash. Each time the button is pressed, the LED will be lit up and the set value can be observed.

2. Pure light control "0" mode: when there is no sunlight, the light intensity drops to the starting point, the controller delays 10 minutes to confirm the start signal, and then the load is turned on and the load starts to work; When there is sunlight, the light intensity rises to the starting point, and the controller delays 10 minutes to turn off the output signal after confirming the shutdown of the output signal, and the load stops working.

3. Light control + delay mode (" 1 "--" 9 ", "0" -- "5") : the starting process shall be the same as before. When the load reaches the set time, the load will be closed. The time setting is shown in the table below. Light control is preferred.

4. General controller mode of solar street lamp battery "6." : this mode only cancels the light control, time control function, output delay and related functions, and retains all other functions as general controller.

5. Debugging mode "7." : it is used for system debugging, which is the same as the pure light control mode. With light signal, the load is switched on; without light signal, the load is switched off. It is convenient to check the correctness of system installation during installation and debugging.

6. Description of output mode: when the LED digital tube display mode is set, the display number without decimal point is "0" to "9" and "0." to "5." mode, the output is pure DC output. If the number does not have the decimal point namely "0" to "9", the digital tube decimal point is not bright.

7. Load connection: connect the load connection line to the load output terminal on the controller, pay attention to the + and - poles, and do not reverse connection, so as not to burn out the electrical appliances.

The above is a lithium battery customization senior engineer for the solar controller how to set up a few methods full summary, I hope to help you, see the site map, you can learn more about the solar controller how to set up more energy and money saving.

of battery Center

Lithium Batteries

Classification by power battery

Lithium battery classification

By other classification

雄厚的企业实力,给您信心

China ofbattery network

  • Lithium ion battery cells

  • Lithium battery manufacturer

  • Lithium battery factory

  • Lithium ion battery pack

  • High quality battery cell

  • 18650 lithium battery manufacturer

  • Famous battery factories in China

  • Lithium-ion battery pack

  • China ofbattery net

  • There are certified batteries

  • Contact:wayson.Li
  • Mobile:+86-13530924650
  • Sales QQ:3020615556
  • WeChat ID:zndcwx
  • E-mail:zndcw@qq.com
  • Address:OFbattery lithium battery club, shenzhen city, guangdong province, China
  • Sales WeChat
cache
Processed in 0.004135 Second.